Get prices to diagnose a heat pump fault in Eyemouth
A heat pump that shows an error code, makes a new noise or no longer warms the house is better looked at early than left running. Note when the fault started and what changed.
Tell us what needs doing at your property in Eyemouth, and up to four independent heat pump businesses may respond, depending on who covers your postcode. Matching costs nothing, and every quote can be declined.
What the engineer will check
Diagnosis starts with the symptoms and error codes, then checks flow rate, system pressure, filters and strainers, sensors, the fan and compressor, the circulation pump and the controls. Work on a circuit containing fluorinated refrigerant needs an appropriately F-gas qualified engineer, and warranty terms may require the original installer or an approved engineer to do it.
What you might be seeing
- An error code on the display or app
- A defrost cycle that never finishes
- Rooms that stay cold or take far longer to warm
- A rattle, hum or knocking from the outdoor unit
- Hot water that runs cool or a cylinder that does not heat
What the engineer does
The engineer should read the fault history before touching anything. A typical job includes:
- Checking the fault code, controller history and settings, and asking what changed before the fault.
- Inspecting the outdoor unit, fan, coil, pipework, filter or strainer, pressures and the cylinder or buffer.
- Measuring flow rates, temperatures, sensors, the circulation pump and electrical supply.
- Repairing or replacing the faulty part, or flushing, bleeding or topping up the system where needed.
- Noting the findings, the work done and any further recommendations in writing.
Repair, replacement or a further visit
Simple faults, such as a blocked strainer or a failed sensor, can often be fixed in one visit. Parts such as fan motors, circuit boards, expansion valves and compressors may need ordering, and a refrigerant leak may need a further visit. Ask for the repair price and the cost of waiting for parts before agreeing.
Access and finishing up
Clear the path to the outdoor unit and leave the indoor unit and cylinder accessible. Have the installation paperwork, the guarantee details and the commissioning certificate to hand so the engineer can check what is covered.
After the repair
Have the engineer explain how the repair was checked. Keep the fault report and part details. If another visit is needed, agree the charge and whether the system can safely run while you wait.
Paying for heat pump fault repair in Eyemouth
Across the UK this work typically costs £150–£1,000. Treat it as a national guide rather than a local rate. A diagnostic visit with a simple fix, such as clearing a strainer or resetting the controls, sits at the lower end. A failed sensor, circulation pump or fan motor is in the middle. Circuit board replacement, a refrigerant leak repair or a compressor fault takes the job to the top of the range or well beyond it.
Have each business explain its equipment and labour costs, any survey fee and the VAT position. Allow 1–4 hours as a guide for the work itself; equipment lead times and awkward access can add to it.
What to tell the business
Give the make and model of the heat pump, how old it is and who installed it. Describe the symptoms, quote any error code word for word and say when it began. Send a photo of the data plate on the outdoor unit if you can reach it safely.
When replies arrive, check what each one includes. Ask whether the call-out and diagnosis are charged separately from the repair, what the labour covers and whether the engineer is trained on your make and refrigerant, with F-gas qualifications where needed. Check whether the repair affects any remaining manufacturer or installer guarantee.
Qualifications and consents
A straightforward repair normally needs no planning permission; replacement or relocation may need further checks. Work on a circuit containing fluorinated refrigerant must be done by an appropriately F-gas qualified engineer, and changes to the electrical supply or hot water system may need certification. If the heat pump is still under guarantee, check with the installer or manufacturer first, because unapproved work can void it.
If you are not sure whether the council needs to know, ask Scottish Borders Council. If the job grows beyond what was quoted, confirm which approvals apply before the extra work starts.
Visits and access in Eyemouth
Give the full postcode for the property in Eyemouth, Scottish Borders. Say whether a van can park close to the property. Include a picture of the error code if it shows on a screen or app. Even adjoining homes can have different heating layouts, so describe your own system.
Looking beyond Eyemouth
Businesses choose their own travel areas within Scottish Borders. Neighbouring postcodes can reach different businesses.
Kelso, Melrose, Jedburgh, Berwick-upon-Tweed, Galashiels, Hawick, DunbarStart your enquiry
Use the free enquiry form to describe the job. Check your guarantee before arranging anyone to visit, and have the commissioning paperwork ready. Businesses that join are asked for insurance details and references. Before booking, check insurance and recent experience of similar jobs. We only pass the enquiry on: advice, pricing and the work itself come from the business you pick.
We cannot send anyone in an emergency. If someone at home is vulnerable to the cold and the heating has failed, contact a business directly. If equipment smells burnt or appears electrically damaged, stop using it and seek professional help; only isolate it if you can do so safely.
Questions homeowners in Eyemouth ask
How can I compare quotes for heat pump fault repair in Eyemouth?
Fill in one enquiry form with your postcode, the heat pump make and model, any error code and when the fault began. It can reach up to four independent heat pump businesses working in Eyemouth. Replies depend on the job and availability. You decide whether to book anyone.
Roughly how much is heat pump fault repair in Eyemouth?
We use £150–£1,000 as a UK guide. Businesses in Eyemouth price their own work, and which part has failed and whether it is in stock affect the total. A written quote should list equipment, labour, VAT and any survey or call-out charge.
What should I do when my heat pump shows an error code?
Write down the code and what the unit was doing, then check the manual for the meaning. Do not keep resetting it. If it returns, ask an engineer to diagnose it rather than trying a series of fixes.
Is ice on the outdoor unit normal?
A light frost that clears during a defrost cycle is normal. Thick ice that stays, or a unit that stops heating while iced up, points to a fault with the defrost, fan or airflow, and should be checked.
Will repairs affect my guarantee?
They can. Many guarantees require work to be done by the installer or an approved engineer. Check the terms before you call anyone else.
How long should I allow for heat pump fault repair?
Allow 1–4 hours as a guide. Ask who pays the call-out if the fault turns out to be a setting rather than a part. Parts availability and further testing can mean another visit. Ask whether heating or hot water will be unavailable while you wait.