Compare quotes for heat pump fault repair in Highland
Frost on the outdoor unit that does not clear, or rooms that are suddenly cold, are common reasons to call someone out. Write down any error code shown.
Send one enquiry for Highland, and up to four independent heat pump businesses may respond, depending on the work involved and who has capacity. Matching costs nothing, and every quote can be declined.
Work to include in your enquiry
Diagnosis starts with the symptoms and error codes, then checks flow rate, system pressure, filters and strainers, sensors, the fan and compressor, the circulation pump and the controls. Work on a circuit containing fluorinated refrigerant needs an appropriately F-gas qualified engineer, and warranty terms may require the original installer or an approved engineer to do it.
Things to mention when you enquire
- The unit locking out with a fault message
- Ice that builds up on the outdoor unit and stays
- Rooms that no longer reach their usual temperature
- Unusual noise from the fan, compressor or pipes
- The immersion element running far more than usual
On the day
Tracing the cause comes before ordering parts. A typical job includes:
- Reading the fault code, controller history and settings, and asking what changed before the fault.
- Looking over the outdoor unit, fan, coil, pipework, filter or strainer, pressures and the cylinder or buffer.
- Testing flow rates, temperatures, sensors, the circulation pump and electrical supply.
- Fixing or replacing the faulty part, or flushing, bleeding or topping up the system where needed.
- Recording the findings, the work done and any further recommendations in writing.
Repair, replacement or a further visit
Simple faults, such as a blocked strainer or a failed sensor, can often be fixed in one visit. Parts such as fan motors, circuit boards, expansion valves and compressors may need ordering, and a refrigerant leak may need a further visit. Ask for the repair price and the cost of waiting for parts before agreeing.
Preparing for the visit
Clear the path to the outdoor unit and leave the indoor unit and cylinder accessible. Have the installation paperwork, the guarantee details and the commissioning certificate to hand so the engineer can check what is covered.
After the repair
Ask what was tested once the repair was finished. Keep the fault report and part details. If another visit is needed, agree the charge and whether the system can safely run while you wait.
Prices for heat pump fault repair in Highland
A sensible planning figure is £150–£1,000. A quote may fall below or above this range. A diagnostic visit with a simple fix, such as clearing a strainer or resetting the controls, sits at the lower end. A failed sensor, circulation pump or fan motor is in the middle. Circuit board replacement, a refrigerant leak repair or a compressor fault takes the job to the top of the range or well beyond it.
Ask for equipment, labour and any survey fee to be listed separately, with VAT stated. Allow 1–4 hours as a guide for the work itself; equipment lead times and awkward access can add to it.
Information that speeds up a quote
Give the make and model of the heat pump, how old it is and who installed it. Describe the symptoms, quote any error code word for word and say when it began. Send a photo of the data plate on the outdoor unit if you can reach it safely.
Go through every quote item by item. Ask whether the call-out and diagnosis are charged separately from the repair, what the labour covers and whether the engineer is trained on your make and refrigerant, with F-gas qualifications where needed. Check whether the repair affects any remaining manufacturer or installer guarantee.
Regulations and approvals
A straightforward repair normally needs no planning permission; replacement or relocation may need further checks. Work on a circuit containing fluorinated refrigerant must be done by an appropriately F-gas qualified engineer, and changes to the electrical supply or hot water system may need certification. If the heat pump is still under guarantee, check with the installer or manufacturer first, because unapproved work can void it.
Council questions for this area can go to Highland Council. Ask your installer which consents they will deal with and which are left to you.
Booking heat pump fault repair near you
Put the postcode and the town or village on the form for work in Highland. Flag shared access, narrow lanes or limited parking. Send a photo of the controller display and the data plate. A nearby installation may have a different heat demand, so describe your own system.
Request quotes for this work
Use the free enquiry form to describe the job. Check your guarantee before arranging anyone to visit, and have the commissioning paperwork ready. Businesses that join are asked for insurance details and references. Before booking, read their current paperwork. We only pass the enquiry on: advice, pricing and the work itself come from the business you pick.
We cannot send anyone in an emergency. If someone at home is vulnerable to the cold and the heating has failed, contact a business directly. If equipment smells burnt or appears electrically damaged, stop using it and seek professional help; only isolate it if you can do so safely.
What to check before arranging this service
How can I compare quotes for heat pump fault repair in Highland?
Fill in one enquiry form with your postcode, the heat pump make and model, any error code and when the fault began. It can reach up to four independent heat pump businesses working in Highland. Replies depend on the job and availability. You decide whether to book anyone.
Roughly how much is heat pump fault repair in Highland?
We use £150–£1,000 as a UK guide. Businesses in Highland price their own work, and which part has failed and whether it is in stock affect the total. A written quote should list equipment, labour, VAT and any survey or call-out charge.
What should I do when my heat pump shows an error code?
Write down the code and what the unit was doing, then check the manual for the meaning. Do not keep resetting it. If it returns, ask an engineer to diagnose it rather than trying a series of fixes.
Is ice on the outdoor unit normal?
A light frost that clears during a defrost cycle is normal. Thick ice that stays, or a unit that stops heating while iced up, points to a fault with the defrost, fan or airflow, and should be checked.
Will repairs affect my guarantee?
They can. Many guarantees require work to be done by the installer or an approved engineer. Check the terms before you call anyone else.
How long should I allow for heat pump fault repair?
Allow 1–4 hours as a guide. Ask who pays the call-out if the fault turns out to be a setting rather than a part. Parts availability and further testing can mean another visit. Ask whether heating or hot water will be unavailable while you wait.